Amtrak's Secaucus High Density Cab Signaling in Action

When the Secaucus transfer was being designed and built around the year 2000, Amtrak implemented a new "High Density Cab Signaling" concept with shorter blocks and additional cab signal codes in order to increase the capacity of the approach into Penn Station especially with all the NJT Corridor and Midtown Direct trains stopping at Secaucus. This would replace the PRR era Rule 261 signaling with mile long blocks. Below we see the 2E signal at ERIE interlocking cycle through its indications after an eastbound NJT push-pull takes a Clear signal upon departing the track 2 station platform. 2E was fleeted for a normal route and immediately went to Stop and Proceed, then Slow Approach, Approach, Approach Limited and  finally Cab Speed (which could represent both 60 and 80mph speed codes). The horn at the end was an approaching Amtrak Regional which ultimately took 2E at Clear (not captured on video).

Unfortunately this was just in time for NJT to lean into Push-Pull service which lacked the acceleration to and braking systems to take advantage of the rapidly changing speed codes. On push-pull sets with traditional air brakes, crews would often target one speed below the one being displayed to avoid jerky train handling and the risk of penalty brake applications in the face of frequent cab signal drops.This negated much of the intended speed benefits from the high density cab signals. For whatever reason, similar High Density Cab Signals could be found on the 2005 era western Harrisburg Line re-signaling, however due to the low traffic density, Amtrak has taken to disabling some of these extra code change points.

View From the Head End

Recently a Youtube channel appeared called View From The Head End, that was posting complete head end cab videos from Amtrak trains. These were not the more typical "reversed" videos taken from a rear facing window, but legit head end videos that documented both signals and signaling. More significantly the videos were up to date, likely all recorded within the last couple of years. My first thought was that someone had recently retired because since the early 2000's Amtrak (and I assume most railroads) have been somewhat anal about employees moonlighting as content creators. Well, I guess they hadn't retired because if you haven't noticed the link is broken and the entire channel is gone.

While the practice of workers recording head end videos to feed Youtube channels seems to be quite common in Europe (where I should add its practically impossible to fire railway workers), there are surprisingly few full-line inside-the-cab videos from North America. Up through the early 2000's there was a cottage industry head end videos being sold at "Train Shows" on either VHS or DVD. Some of these were professionally produced by outfits like Pantex, while others were made by AV savvy employees with access to a Hi-8 camera and a capture card. Unfortunately the rise of The Internet brought this wildcat era of video to an end as the speed of information made it easier for previously underground works to become known by regulators, the media and lawyers.

In the early years of Youtube, spotty internet connections and the more ephemeral nature of online data encouraged folks to save off important video content like head end videos. This practiced has decreased as the internet became more reliable overall, however when you find something that seems too good to last, you might want to leap into action and save off a local copy. In a sliver of good news I was able to watch some of the videos before they vanished and resolve some outstanding signal questions I had.

Meanwhile if you'd like something similar to watch I can provide two pairs of videos from the late 2000's covering an Acela trip from Boston to NYP (head end) and the Former Conrail Chicago Line between Buffalo and Albany (rear facing). Intended for Train Show (tm) sale both had been scrubbed of ambient cab sounds and the Chicago Line also being video reversed (which I was able to undo). Although mostly silent, the Chicago Line video in particular captures the NYC/Conrail signaling immediately before its complete replacement ~2010.

Caltrain EMU Cab Video Signal Survey

After the loss of the Caltrain gallery car railfan window I wasn't holding out much hope for having anything worthwhile to do on the Caltrain system as European spec rolling stock typically come with bulkhead style cab doors. However videos have been appearing showing that front facing views are present. This have the added benefit of providing a southbound signaling survey as previously such photos and videos were only possible facing northbound. 

I have already covered changes between San Jose and Tamien and can now confirm that the remaining Southern Pacific style signals in the terminal area have been replaced. The good news is that the few SP target type signals on the north end near the tunnels are still in place although unfortunately the triple unilens stacks at CP-COMMON were replaced by a standard LED modular type in a three virtual head configuration. Another note is how bad the sight lines for some of the wayside mast signals have become. This makes clear the advantage for position lights and cab signals in electrified territory. Although the freight spec PTC system Caltrain uses is kinda like a cab signal, moving to a Rule 562 coded track circuit arrangement might save them a lot of trouble. 

You can watch the video for yourself, but despite the hype the weekend and daytime local service is still highly underwhelming with little in the way of interesting signaling or routing. Although faster than diesel, the speeds are still slow compared to a limited stop run and unfortunately these have been largely curtailed with the fastest peak period trains still 3 or 4 minutes slower than the famed 4 or 5 stop Baby Bullets of the 2004-2024 time period.

The Enthusiasts Step Up

Unlike Europe, Heritage railroads in the United States never developed a vintage signaling component beyond what one might describe as display items. The big reason for this is that in service signaling and interlocking appliances have significant regulatory inspection, testing and documentation requirements that are beyond the reach of most tourist train operators. The result has been that most preserved towers are completely inert, with just a handful having interactive elements such as operable interlocking machines (SS43 BERK) or full on simulations (HARRIS). However, in recent years it seems that the private collector/enthusiast space has been stepping up to fill the gap as exemplified by the small YouTube channel Laser 711.

Signal and signaling equipment collectors have been around for some time, snapping up such items as model boards, CTC cabinets, full size signals and even interlocking machines. Until recently, railroad signaling departments would tend to keep their retired equipment, as similar vintage hardware was still broadly in service and the parts to maintain them were no longer being manufactured. However, the PTC related re-signaling push rapidly phased out so much of the relay era railroad signaling that the equipment is now being sold for scrap or offered free to anyone with the capacity to haul it away. 

In the context of interlocking towers, model boards and CTC cabinets have been widely collected for some time as switch to video display in a dispatch office had long ago destroyed their reuse value. Somewhat ironically, it was the older mechanical and electro-mechanical interlocking machines that retained the most value as a source of spares for their kin.  (For example a major reason LENOX tower near St. Louis was closed was to supply parts to the CNW LAKE ST machine in Chicago.) However as the number of these in service interlocking machines hit zero, anyone with a large enough truck could cart the survivors away for their own personal amusement. This is where Laser 711 comes in, having apparently set up not just a HARRIS style PLC backed simulation, but the full hardware stack including relays, point machines and signals.

 He has also restored an ex-Erie CTC console from BK tower along with its original code system, and now appears to be in the process of implementing as much field functionality as possible "in relay".

Of course it would be great if more publically accessible museums were able to step up to the plate with functional period correct signaling equipment, but the signal enthusiast community, powered by recent advances in the "maker" scene and high capacity pickup trucks, seem to be taking up a lot of the slack. Just like we have seen with the extensive telecom switch collection of Step by Step Phil, these private efforts stand a good chance of eventually finding their way into durable preservation.

Attempted CTC at the Seashore Trolley Museum

I will also mention that non-FRA regulated streetcar/transit museums have the best capacity to implement "live" historic signaling. When visiting Shoreline Trolley Museum I was shown their "in-progress" CTC system that they were building from thousands of relays donated by Amtrak and Metro North.

 

The fact that I have not heard much if anything about that project in the past 20 years hints at its priority in the greater scheme of things, but all it takes is the right team of enthusiasts to get a project off the ground.

Mr. Beast Fakes the Trolley Problem

For those of you who don't know, "Mr. Beast" is one of the most popular figures on YouTube mostly appealing to 11-14 year old males with formulaic content that tends to involve giving away large amounts of money in novel ways. To get value from this post you do not need to know who Mr. Beast is and I am not recommending you view his content. In 2024-2025 Mr. Beast produced a 10 episode reality TV show for Amazon Prime titled "Beast Games". While watching an in depth third party review/breakdown of Beast Games, I noticed something in the 7th episode the pulled back the whole reality TV artifice a little farther than normal due to my knowledge of how railway signaling and operating rules actually work and I figured I should share it with the class.

The premise of the 7th episode, entitled "Elimination Train" was to set up a trolley problem scenario with full a size AAR locomotive and rolling stock on a Canadian short line. Chosen players would be placed on a surprisingly realistic fake signal bridge with a prop "lever" situated perpendicular to the track. They would then have to choose to direct the train either towards a high value vehicle they could win or representations of their team members facing elimination. (Note, this isn't a faithful representation of the trolley problem which tries to explore the morality of action vs inaction.) While the overall show suffered from a lack of play testing, they did manage to coax one of each outcome for this event.

Anyway this is where the fakery of reality TV becomes visible to anyone with rail knowledge. The sequence begins with the contestant "choosing" the car over the other contestants with the "lever" placed in the reverse position. However to keep up the drama its made clear that he can still change his mind at any time until the train passes the switch like in the conceptual trolley problem. As the full sized locomotive with one car in tow appears out of a smoke effect and approaches the switch the episode went into overdrive with rapid cuts, fast-mo, slow-mo and insert shots trying to build the suspense to see if the contestant will change the direction of switch.

However in every wide shot where the switch and the locomotive is visible, the points are shown to never move from their initial position, even if an insert shot shows the pints moving or the contestant moving the lever. The scenario is run more than once, in one the points are reverse and stay reverse and in the other they are set normal and stay normal. While this might fool the casual viewer, for the rail-informed watcher will know the fix is in once the locomotive appears and is moving faster than a jog, because there is no way in hell some shortline was going to allow the producers (and by extension the contestant) to actually solve the trolley problem and derail their locomotive. To the show's credit the switch mechanism was never shown in detail and the area around where a hand throw switch stand would be was intentionally hidden from view, however I am not sure how much this ultimately mattered for the viewers given the moving points were only shown in extreme close-up.

Here's what I believe went down in the actual production. First, while technically possible, its highly unlikely that a short line would have rigged up a power assist switch to the prop lever when a hidden grip could easily do the same job. The contestant was given some amount of time to make his choice while literal man behind a curtain followed the position of the lever and used the hand throw stand to align the switch points for the benefit of all involved. Then at some point, possibly even before the locomotive emerged from the smoke the choice was set and the train was allowed to do its thing. All of the drama was then manufactured in the editing room.

That's the irony of the situation. The show theoretically sets up a contestant the chance to solve the trolley problem, but doesn't have the balls (or insurance coverage) to actually allow the contestant to solve the trolley problem. What people don't get about the trolley problem is that the choices you are given aren't the only choices that exist. If one puts the points on center, the trolley derails and comes to safe stop. This is how split point derails work after all. (Conversely if you throw the points after the first truck passes over them, but before the second, you can get the trolley to drift and kill both sets of people tied to the tracks.) The real life trolley problem tries to set up a binary choice to explore an moral dilemma, however the mechanics of the problem allow folks with knowledge and the ability to think outside the box to make a choice where everybody lives. That's the important takeaway. If presented with a no-win scenario, you change the conditions of the test. 

BTW, if you want to see how The Simpsons got an NYC Subway interlocking tower surprisingly right, check out this post here.

A Video Guide to French "Poste d'Aiguillage"

Getting information on interlocking tower / signalboxes outside the anglosphere can be a bit difficult not only due to the language barrier, but also cultural difference about railfanning and content creation.  While I found a comprehensive site on German towers many years ago, similar resources for French signaling had yet to pop up on my radar. This is rather unfortunate as I believe that France has a strong tradition of staffed towers and electro-mechanical era power interlocking machines.It also doesn't hurt that the standard SNCF model board design gives off strong PRR vibes.

Anyway, when doing a quick Youtube search on "Poste d'Aiguillage" I found a somewhat recent public information film detailing the many styles of French interlocking machine, running the gammut from mechanical lever frames to VDU area interlockings. It even gives a shout out to a North American pattern Taylor (GRS) machine. You can watch the whole thing for yourself below.  Enjoy!

 

 

 

When Urbex Meets Signaling

While there is a lot of crossover between the urban exploration (Urbex) community and the rail enthusiast community, the Ven diagram doesn't quite work the way you think it does as there is both the type of enthusiasm the individual is involves with (rail, urbex or both) and the type of things they explore.  When railfans explore rail stuff, they tend to put the resulting content in the rail bin, even if they are also into Urbex.  Qualified railfans know the jargon and historical details to properly label their content, rendering it searchable and discoverable. On the other hand, Urbex people who aren't railfans, can get into a lot of interesting rail places, yet have little idea of what they are looking at, therefore harming discovery.

Not so long ago I found some critical WINSLOW tower interior photos from 2003 on an urbex blog site that just hadn't happened to appear on casual google searches until recently. In the same vein, I also found a great exploration of the former PRR MG tower on the famous East Slope between the Horseshoe Curve and the summit at Gallitzin. I routinely search for new "interlocking tower" videos, but not "switch tower" because the genericness of the term returns a lot of bad results.  It was only after several years would YouTube searches include this video in my interlocking tower search due to the key words in the comments.

Despite their lack of historical context, the Urbex community can assist the railfan community by being willing to generally take more risks than railfans. In this example MG tower is known to see increased police patrols to the point where the risk of visiting is well known.  On the other hand, Urbex folk don't care about getting train photos and can put more effort into not being see in addition to just having more experience in not being seen. Therefore, while railfans steered clear of MG, this guy was able to made a comprehensive video documentation. Another popular urbex assist has been the Hoosac Tunnel in northwestern Massachusetts, which sees both explorers and ghost-hunters occasionally getting some footage of the searchlight signals inside.   

Anyway, the next time you are looking for some open source intelligence on some hard to access signaling artifact, try to use some urbex search terms. You might find something surprising.

2024 NEC Reference Video

 A side effect of Allan Fisher's recent "Festival Express" style journey from New York to Saint Louis in a private car full of transit Youtubers was a 3 hour and 22 minute long high definition rear facing railfan video of the entire Amtrak Northeast Corridor between New York and Washington. The video was filmed from the PV's position behind Amtrak's westbound Cardinal Train 51 with no observable delays and a top speed of 110mph.

This video is an important historical artifact as it captures certain NEC elements that are under imminent threat of replacement including the PORTAL bridge and Baltimore's B&P tunnel complex as well as all of the associated signaling that will likely be part of upcoming Rule 562 expansions. I was also able to confirm some recent changes such as the replacement of the pneumatic A-5 point machines at GRUNDY interlocking with electric M3's. If you have any questions about current NEC layout, this is the resource for you.

1994 SUISUN BRIDGE Cabin Tour

 Movable bridge cabins are the invisible step children of the interlocking tower scene, but its easy to forget that they have all the same stuff that regular towers have including the full compliment of electro+mechanical interlocking machines. While poking around YouTube I found this video of someone's 1994 tour of the Souther Pacific's SUISUN BRIDGE movable bridge cabin. This vertical lift drawbridge is a crossing of the Carquinez Strait, which connects Suisun Bay with San Fransisco Bay and hosts Amtrak's Capitol Corridor, Coast Starlight and California Zephyr services.

As far as I am aware it is still a staffed interlocking station, although I am not sure if it retains the US&S Model 14 machine and panel seen throughout the video (specifically 10:30). In the video you can also hear the sound of a signature US&S pneumatic switch machine at 4:00 as it locks down the lift span under the control of a Model 14 lever.

Based on intro and outro clips of ABS searchlight signals on the south bank, I suspect this pre-dated the era of SP style tri-light signals that remain at the bridge today and therefore implies that the Mode 14 was replaced by a panel or VDU.

Westbound home signals SUISUN BRIDGE

The panel shown at various points in the video also lacks the VISTA crossover immediately west of the eastbound signals.

Westbound home signals VISTA interlocking with eastbound home signals SUISUN BAY

So it looks like the "Southern Pacific" style re-signaling was going on quite a bit later than I had figured what with the mid-90's Union Pacific merger.

A New Source for Railfan Window Videos

While trying to gather information for my recent SEPTA Unilens post, I discovered a newish railfan video channel with a large amount of up to date of front facing video content that can help with signaling research. Retired  Railfan Horn Guy has been crisscrossing the country shooting a mix of front window and standard videos with special emphasis on SEPTA and, more recently, Caltrain. The latter is particularly useful given the impending demise of forward facing views on that line.

The guy is based on Long Island so naturally there is LIRR content, but he doesn't seem to have the same level of access as some of the other LIRR specific video channels that I suspect have insider access. Anyway, its a fantastic channel and good resource to bookmark.

LIRR East Side Access Signaling Surprises

When the LIRR's new East Side Access opened to Grand Central Terminal earlier this summer and I was expecting the signaling to follow the pattern of the LIRR's other recent projects with the new reduced aspect signals like G/L that have become the new standard. However, now that cab view videos have become available the new signaling setup came with a few surprises.

Once trains enter the ESA tunnels at HAROLD interlocking they are exclusively presented with transit style 3-lamp signals displaying single light Green, Yellow and Red aspects. Although these two videos can't necessarily reveal all possible operating conditions, the lack of anything aside from Green, Yellow and Red over both straight and diverging routes implies that those are what one gets in the ESA tunnels even with track speeds up to 45mph. It also appears that intermediate signals are provided in the few parts of the route that have significant distance between interlockings.

I suspect that the decision was made to lean on both the track speeds and speed code based cab signals to simplify the ESA wayside signaling based on the LIRR's existing practices before the implementation of the Reduced Aspect Signals. Remember, ESA has been under construction for almost 20 years and the design work was likely completed a decade before the Main Line capacity expansion projects motivated the new signals. A review of the videos shows a combination of diverging routes at the prevailing line speed (15, 30 or 45mph) or sufficient distance between the signal and the turnout for a cab signal code drop to take effect. On the outbound video there appears to be an unprotected slow speed crossover so I am not sure if that would rate Green signals over cab drops or a Yellow approaching a flashing red or what. I made some inquiries and I will post an update if those pan out.

All in all, the signaling is more interesting than an endless string of Green over Lunar and the use of US&S transit style signals is nice, but its unfortunate we didn't get a full set of LIRR "tunnel" signals similar to the Atlantic Ave branch.

The Final Months at AC Tower

Looks like the Railroad Media Archive has done it again with a video covering the last few months of operation at the former Erie AC tower in Marion, Ohio from November 1994 to just before its closing on January 18, 1995. AC tower was located at the crossing of the compass east-west Erie and Big Four (NYC) with the compass north-south N&W and C&O.The Erie and Big Four alignments would be merged into Conrail and eventually became the Indianapolis Line on a largely Big Four routing with the Erie RR main being largely abandoned. By the mid-90's it was finally time to retire the old Taylor Model 2 machine.

In the video the things of note are the various communications duties of a tower operator and the lever manipulation sequences, specifically the use of crossing lock levers to set the direction of travel through a diamond. 

AC Tower model board and manipulation charts as preserved.

Although the tower was closed in 1995, it was moved to the nearby station grounds and preserved as a semi-restored museum. Hopefully they will get the expertise to restore it in a similar fashion to HARRIS. Because of the "lateness" of the conversion, the N&W and C&O signals were retained on the two non-Conrail routes until about 2012.

Interlocking Tower Audio Recordings

I've featured the work of the Youtube channel Railroad Media Archives before, but in the last few weeks they have taken a page from Evan Doobell's playbook with interlocking tower audio recordings from the 1960's and 70's. As you might be aware, the ability to capture long duration video information lagged the ability to capture long duration audio information by something like 5 decades. This means that recordings of interlocking tower operations in an audio/video format wasn't really feasible until the late 1970's, at which point everyone's favorite flags had fallen and conglomerates like Conrail and Amtrak were large and in charge.  While a great deal of vintage signaling technology was in use up through the 80's, 90's and Today, radio was well established along with its attendant operating practices such as track warrant control. 

Anyway,  Railroad Media Archives has so far posted three of these tower audio recordings covering HEATH and SUMMIT towers on the joint PRR-B&O C&N (Columbus & Newark) Railroad in Central Ohio as well as HIGH ST and MOUNDS towers in Columbus, OH. 

Hopefully we'll get to hear more of these sorts of recordings. They can certainly come in handy for any time one might be otherwise inclined to listen to radio.

Reading and Northern Video Update

 It's been a good while since my last Reading and Northern update and although there's been nothing earth shattering I was recently tipped off to a cheat code when it comes to exploring the generally less accessible northern division between Scranton and Jim Thorpe. With the general collapse of any other interesting signaling in the region I have been been putting additional time and effort into getting photos of the R&N's newly installed CTC signaling between Reading and Jim Thorpe.  However while the R&N inherited some interesting bits of signaling from the Conrail era, most of it reachable either by boat or long hikes along 20 miles of inaccessible right of way in the Lehigh River Gorge. My Plan A was to try and grab a seat on one of the many R&N passenger excursions however the summer 2020 one was cancelled by Covid and the recently announced one in May 2023 quickly sold out. 

However one of my fantastic readers linked me to a speeder enthusiast's Youtube channel that included a 2022 speeder trip from Reading all the way to Pitson Yard north of Scranton, which is pretty much the entire R&N CTC'd main line. This basically provided all the signal status information you need for either fact of existence or for planning more involved photo trips. Part 1 covers Tamaqua through White Haven in a very respectable 90 minutes with part 2 White Haven to Pitson.

If you don't want to spend 3 hours watching the videos the TLDR is between CP-COAL and CP-WHITE HAVEN the LVRR signaling has been replaced by square Safetran CL-10 modules in a target/tri-light configuration. Between White Haven and Glenn Summit is where the LVRR searchlights appear and finally between Glenn Summit and CP-DUPONT is the land of 1980's non-modular GRS traffic lights.

Aside from closing the gap between the Hometown viaduct and Jim Thorpe, I'm not sure how much more the R&N is planning to expand its CTC, but whatever they do I'll be sure to report on it here. Meanwhile I will continue to gather R&N signal photos for additional less current events type posts.

NEW LIRR Front End Videos and News

The (temporary?) return of Budd M3 Metropolitans to LIRR service has resulted in a bevy of head end railfan window videos from Youtuber Mr Master 767 including the new Main Line third track arrangement between DIVIDE and QUEENS interlockings. I figured I would post some of the videos and then provide some quick commentary on the key points of interest.

On the Ronkonkoma to NY Penn segment above we can see the final result of both the Ronkonkoma double track and Main Line Third track projects. The good news is that BETH and both core and extended parts of DIVIDE interlocking remain position lit, however the new MNRR style reduced aspect signals have taken over all other portions of the route to QUEENS interlocking.  At this point QUEENS is scheduled for additional re-signaling and re-configuration with BETH and DIVIDE to follow in subsequent years unless the MTA's financial situation heads this off.

In the above Atlantic Branch video we can see that DUNTON interlocking is still largely position lit, but point machines are now electric.  VAN interlocking has also been converted to electric, but BROOK appears to be holding on with some remaining pneumatic. 

On the Long Branch Branch LEAD interlocking has been converted to non-reduced color light (probably several years ago), no word on the status of LEAD as a manned interlocking station however.

Finally on the Port Washington Branch a reconfiguration of NECK interlocking appears ready to see the replacement of multiple position light masts, gantries and pedestal signals including the practically brand new westbound signal bridge. This is accessible from the station and is definitely on my To Do list.

1992 Video of A (Tower) and ZOO Operations

 I caught a tweet showing off some on Pentrex videos that had been uploaded to Archive.org documenting Amtrak's 1992 vintage Northeast Corridor.  I've seen a number of these before and they are a pretty by the numbers affair with a mix of cab and trackside VHS grade video shots with occasional narration explaining things I already know.   Well this time, on a hunch, I scanned through the runtime and discovered some rather lengthy segments filmed inside A and ZOO interlocking towers when they were open and handling NEC operations. A would be taken over by the new Penn Station Control Center in 1994 and ZOO would have its NEC functions transferred to CTEC in 1999.

The A tower segment begins at 6:10 and the ZOO tower segment begins at 1:06:45.  Some interesting things to note is that A was staffed by a train director, two levermen and three assistants to the train director, although one or more may have actually been telegraphers.  In 1992 most of the northern NEC would have been tower controlled with HUDSON closing in 2003, DOCK in 2017 and UNION in 2009. ZOO is staffed by a daytime crew of 4, a train director, leverman and two assistants to the train director, although I was informed that one of these assistants would be responsible for the NEC portion of the interlocking machine under supervision of CTEC. In 1992 ZOO was still hangling Conrail moves over the High Line.

 Anyway enjoy.  Hopefully this video will continue to fly under the radar and stay online.

A Tale of Two British Railway Signaling Public Information Films

 The UK is well known for a certain style of public information film that were professionally produced up through the 1980's. A couple go into great detail into the ins and outs of Railway Signaling and served as both a way to increase the public standing of the nationalized railways network in a time of both austerity and modernization and as a recruiting tool to bring new workers with new skills into said modernizing rail industry. 

The first film, entitled Electrical Engineering on the Railway and produced in 1962, falls more on the recruiting side of things as relay based "electric" signaling replaced largely mechanical manual block signaling on the busiest unresignaled main lines of British Rail. While this may been a bit odd as North American signaling has largely discarded purely mechanical signaling by the 1920's, Britain might get a bit of a pass given the toll a pair of World Wars took on its railways and economy.  Point of note include:

• A general lack of safety practices including, but not limited to protective clothing and burn pits for demolished signalboxes.
• The appearance of pneumatic point machines and North American supplied GRA Model 5A electric point machines.
• Rather flimsily looking track circuit bonding wires.
• The continued construction of brand new mechanical lever type interlocking frames.
• Some components of interlocking hardware being hand forged in house.
• A general use of North American pattern glass case plug-in and shelf type relays.
  

The second film, entitled Points and Aspects, was made in 1974 and shows the leap in British signaling from what one might call an updated basic CTC plan to something that was making far more use of computer and telecom technology to enable the so called wire area "Power Box" era of British signaling with as much automation as 1970's technology could muster..  This film is definitely trying to sell the public on British Rail not being a basket case and is worthy of their continued support and patience.  As a result an emphasis is given to the higher tech elements.

What is especially fascinating is that these two videos appear to span the moment when  the UK went from a very North American leaning approach to signaling technology, to a more European approach. Despite very different operating practices, North America and the UK had very closely aligned signaling supply companies with both GRS and US&S licensing UK technology and then supplying their own products back through local subsidiaries like Westinghouse. In the 1970's we are seeing the end of the glass case relays and Model 5 and M3 point machine that stared in the 1962 film.

British Power Signaling Channel Heads Down Under

About seven years ago I discovered the Youtube channel of one Ian Ives, who had posted a variety of VHS era videos from inside British power signalboxes (PSB's) in the early 1990's, such as this one of Glasgow Central.  Well as the way things tend to go I lost track of the channel until a recent keyword search brought it back on my radar.  It turns out that Mr. Ives has had quite the exciting career as over the intervening years he posted a number of videos from Australian signalboxes.  These are especially interesting due to the mix of British and American influences. 

For example he has some video of the operation of a local Australian copy of the GRS pistol grip style interlocking machine, only in Australia it is paired with pneumatic point machines!

A British style lever frame at Hurstville.

A British style panel controlling a US style CTC layout at Salisbury.

A British style miniature level power frame at Sydenham.

An interlocked and manually controlled grade crossing with a modern panel interface at Parramatta Road.

And finally a modern signaling center at Wollongong.

Just like in the US, Australia has been seeing its own drive towards the elimination of manned signalboxes and non-video interfaces so most if not all of the videos capture railway infrastructure that has been now lost to time. 

In addition to the tower content, Mr Ives has also posted a number of industry training materials including instructions on manual operation of every model of power point machine in service with the railway including pneumatics. 

Please check out the channel as many of the above example videos came in multiple parts. New videos continue to be posted so it might be worth subscribing to.

GRESHAM JCT's Sequence Switches Explained

 Years ago I wrote up a profile of METRA's GRESHAM JUNCTION tower on the Rock Island division south of Chicago.  Not only had GRESHAM JUNCTION managed to stay open into the 21st Century, it was a unique North American example of a sequence switch interlocking. Supplied by the Standard Telephone and Cables Company of London, the interlocking used telecom grade sequence switches to carry out the interlocking functions instead of relays.

In my original post I provide photos of the equipment as well as a general concept of how sequence switches work and some sequence switch interlocking circuit diagrams from the UK, but without time and access to the equipment or someone who was intimately knowledgeable about how it functions, my commentary had to remain at a very high level.  Fortunately, the gang from the Connections Museum in Seattle is on the case because sequence switches is pretty much how Bell Number 1 Panel central office machines functioned (again, as opposed to later relay based technologies). I could try to go into things, but fortunately the museum's YouTube channel has video that is specifically about how sequence switches work. 

Once you see them in action at the Connections Museum, their function in the photos from GRESHAM JCT will become obvious. Of particular note is the function of the magnetic clutch mechanism that rotates the switch spindle. Perhaps if I stare at things enough I can determine what each sequence switch corresponds to in the interlocking.  Is each a complete route? An entrance? An exit? An entrance-exit combination? Let me know in the comments if you figure it out.  BTW, if you like this video take some time to watch the rest of the Museum's content.  It's top notch and does a superb job of explaining some normally opaque topics in the realm of pre-modern telephone switching technology.

Presenting PRR Main Line Towers in the 21st Century

Well, once again I put my hand up to do a program for an NRHS Chapter meeting and since it was for Philly Chapter instead of West Jersey I was able to partly re-cycle my 2008 presentation on Pennsylvania Railroad Interlocking towers on Amtrak's Harrisburg Line.  Of course back in 2008 ZOO, OVERBROOK, PAOLI, THORN, PARK, LEAMAN, CORK and STATE was not only open, but relatively intact.  Fast forward 14 years and only THORN, PAOLI, OVERBROOK and ZOO remain with the first two clearly on their way out. 

 My plan was to refresh the presentation with the updates and refreshed photographic content (including from my 2019 THORN visit).  The reality was that the quality of my 2008-edited photos was woefully inadequate and it took me a good 5 hours to get everything up to snuff. To avoid any awkward dead air I preformed a two hour practice session on my live stream and that is what I am now able to present to you.  There are a few hiccups here and there, but overall I am happy with the result.

Ironically the live chapter presentation had to be split into two parts because a number of Philly chapter members take SEPTA to the meetings which limits the duration to an hour. 🙄